Currently out of stock
Coombe Millennium II clipless bicycle pedals provide superior performance over Speedplay, Shimano, Look and Time.
Coombe Millennium II bicycle pedals feature a patented triple row bearing designed for high performance. cycling.

Contact us at:
Coombe Pro Pedal Systems is a division of W Coombe Engineering Ltd.  Copyright 1998 - 2020
Built to last a lifetime, the MILLENNIUM II's integrated bearing arrangement incorporates dual rows of roller bearings
positioned around a central row of ball bearings. The patented design is extremely compact, yet offers the lowest
friction and highest load rating of any pedals' bearings, providing increased performance and reliability.
Millennium II axles are made with heat treated, high strength
stainless steel, and are generously sized for maximum
rigidity and power transfer, with up to 50% less deflection
under load than competitors' steel axles.

While some competitors offer axles in 6/4 titanium,
when made to the same dimensions as steel axles
(as is required for compatibility) these are only about
60% as rigid as steel, and the slight weight savings
is more than offset by the energy lost due to the
increased flexing of the axle.

Coombe axles are through hollowed for weight reduction
approaching that of solid titanium axles, but provide the
superior strength and rigidity that only steel can offer.
Designed to put maximum power to the pedals, the
MILLENNIUM II shoe cleats are made of rigid, high
strength and wear resistant bronze alloy.

The cleats provide 6 degrees of float, and mount to
standard road shoes using the two side by side
eyelets of the 3 hole pattern.

The Universal Cleats (shown under the "Ordering
Information" section below) are supplied with all
three mounting holes (yellow/green/blue) for
fore/aft adjustability.

Cleats with fixed mounting holes for either yellow,
green, or blue line mounting positions, are available
by special order.  

The "Green" line cleat (shown) positions the axle
directly in-line with the bolt hole centers of the shoe.   

The "Blue" cleat positions the axle 4mm behind the
bolt hole centers of the shoe, moving it closer to
the arch of the foot for greater support and less
strain on the muscles/tendons of the lower leg.

The "Yellow" cleat positions the axle of the pedal
4mm in front of the bolt hole centers.
COOMBE cleats enable
positioning the axle "1"
closer to the arch for
better support, increased
performance, and less strain
"S", than in position "2", as
used in most other systems.
Coombe Millennium II cleats feature integrated walking pads.
MILLENNIUM II shoe cleats feature aerodynamically sculpted,
hard rubber walking pads. The pads insert into the rear of
  the cleats and are simple to replace when worn.
      Combined with the exceptionally low profile
          of the cleats, off the bike mobility
            is faster and safer than ever.
Patents Pending
Coombe Millennium II clipless bicycle pedals feature a super low stack height for maximum performance and biomechanical efficiency .
Coombe Millennium II clipless bicycle pedals feature a patented retention mechanism that provides unrivaled performance and secure engagement.
MILLENNIUM II shoe cleats are aerodynamically
sculpted, low in profile, and provide +/-3 degrees
of knee friendly float. The pedal bodies recess
into the cleats enabling an 11mm total stack
(pedal + cleat) the lowest of any 3 bolt system.
Stack Height: 11mm (pedal + cleat)
Cornering Clearance: 37 degrees
Bearing System: 2 rows needle & 1 row ball (patented)
Float Angle: +/- 3 degrees from center
Retention Mechanism: Tongue and groove "twist-in" to engage (patented)
Pedal Weight: 110 grams each (all stainless steel)
Cleat Weight: 55 grams each (heat treated bronze)
Q Factor: 53.5mm* (crank face to pedal center)

* Note: Optional axle lengths providing 50.5mm and 58.5mm Q factors are available by special order.

Visit us on:
Built for the world's strongest sprinters, the MILLENNIUM II's patented "twist-in" tongue and groove
retention mechanism is rock solid, transferring power directly into the cranks without any flexing
between the cleat and the pedal body. The simplicity of the design provides improved security
and reliability by eliminating the spring loaded latches, and plastic parts, used in other systems.
The bearings are protected by lip and labyrinth seals, and the hollow axle is filled with a grease reserve. This enables
the seals to be flushed by simply pressing the grease plunger (shown above) about 2mm further into the axle every
2-3 thousand miles. With proper lubrication intervals, the bearings will last for the lifetime of the pedals, while
providing increased performance, and lower cost of ownership, than any other "high end" pedal system.

Engineered from the inside-out to deliver more power to the cranks
than any other pedal system, COOMBE MILLENNIUM II pedals use
a state of the art axle and bearing design, along with a patented
twist-in retention mechanism, to achieve unrivaled performance.

Proudly made in the USA, no expense has been spared in building
the world's finest pedal system. The axles and pedal bodies are
precision machined from aerospace grade stainless steels, then
heat treated and cryogenically processed for unmatched durability.

Learn more details below...
Coombe Millennium II pedals come with a five year warranty against defects in materials
and workmanship (normal wear excluded).

To purchase the pedals, contact your local dealer, or order direct with our risk free,
unconditional 60 day money back guarantee.

Please view/print the
on-line instruction manual prior to ordering, and contact us if you
have any questions. Thank you.
Millennium II Pedal Set with Cleats
Millennium II Universal Cleat Set
Out of stock
Millennium II Walking Pads
In stock